- Position your TV so it's at least 42 inches (106 cm) above the ground and at least 12 inches (30 cm) above the fireplace.
- Mark the holes for your wall bracket on the fireplace and drill them with a hammer drill and masonry drill bit.
- Follow the instructions that come with your wall mount and TV bracket to finish installing your TV on the fireplace.
Hang your TV at least 12 inches (30 cm) above the fireplace.
Proper spacing protects your TV from heat and smoke damage. Ideally, your TV should be far enough from the fireplace to prevent the heat from affecting the screen. To be safe, hang your TV at least 42 inches (106 cm) above the ground and at least 12 inches (30 cm) above the fireplace. Make sure there’s an outlet close enough to the installation position for at least an extension cable. If there isn’t one, you may need to hire an electrician to install a new outlet. Having a mantle that’s at least 2.5 in (6.35 cm) wide can help protect the TV from the heat produced by the fireplace. Set up heat-moving fans to help prevent the fireplace heat from rising directly in front of the screen. If you're worried about the mortar between the bricks holding, test it with a hammer drill by drilling a hole into it that’s out of sight (somewhere behind where the TV will go). If the mortar is flaking and brittle or cracking along the edges, it's probably too thin to support a TV.
Mark the drill holes.
Hold the bracket in place against the wall and mark the holes with a marker. Choose a wall mount made from high-quality materials (like stainless steel) that can support the weight of your TV. Use the wall bracket that comes with the mount as a guide for the position of the holes. Then, use a level to confirm that the holes are straight and spaced correctly for your mount. Try to position your holes in the brick itself rather than the mortar in between. Mortar is much softer than brick, so it's less likely to hold a lot of weight. Strips of tape can also work as a marker.
Drill holes into the marks.
A hammer drill and masonry drill bits help cut through brick more easily. Start by gently pressing the drill trigger to get the initial holes drilled. Then, press firmly to drill the rest of the hole into the brick. Plan to use either either concrete screws or concrete strike anchors (that come with a washer pre-attached) when working with brick. Check the packaging that came with your concrete screw or anchor to confirm how deeply you need to drill. It can also help to place the screw/anchor alongside your drill bit to measure the length and then wrap painter's tape around the circumference of the bit (so it matches up with the length of the screw). Once you reach the tape, you’ve drilled deeply enough. Slip on a pair of safety glasses to protect your eyes from dust, and have a broom or shop vac on hand to clean up the mess.
Secure the TV bracket to the wall.
Use your pre-drilled holes and the bracket openings as a guide. For concrete screws, use a drill to secure them into the pre-drilled holes. For strike anchors, use a hammer or rubber mallet to knock the spikes into the pre-drilled holes. Once the spikes are all the way in, use a wrench to tighten the screws around the spikes. Both concrete screws and concrete strike anchors are removable, so it’s okay if you don't position them right on your first try. For screws, have a #3 Phillips-head bit ready to go. Ask a friend or family member to hold the mount in place while you drill the screws in or hammer in your wall anchors. Avoid sleeve anchors and drive anchors. While they can handle a lot of heavy-duty strength, they can't be removed once they're hammered in.
Connect your TV to the wall mount.
Attach the brackets to the back of the TV before putting it on the wall mount. Follow the instructions of your specific mount. In most cases, simply attach the bracket to the back of the TV using the provided fasteners. With another person’s help, carefully lift the TV and line up the brackets to settle it on the mount.
Use a cord concealer to hide cables.
A cord concealer keeps your cables from hanging in front of your fireplace. Cord concealers can be run along the walls and come in colors to match your furniture; plus, they help lead the cables cleanly to an outlet. Eliminate all possible hazards by trying to bundle your cords with a cable sleeve to help keep them hidden from sight. For a more creative option, try painting the bricks of the fireplace to match the colors of your wires. You can also incorporate your wires into a painted wall design.
Comments
0 comment